N76E003_24L01/Home_Light_V0.1/MAIN.C

/******************************************************************************/
/*                        -- 深圳安信可科技有限公司 --                        */
/*
//  文件名：main.c
//  说明：供客户测试模块通信使用程序
//  编写人员：
//  编写日期：
//  程序维护：
//  维护记录：
//
//
*/
// 免责声明：该程序仅用于学习与交流
// (c) Anxinke Corporation. All rights reserved.
/******************************************************************************/
#include "typedef.h"
#include "gpio.h"
#include "uart.h"
#include "nrf_24l01.h"
#include "delay.h"

/******************************************************************************/
// 函数名称：main
// 输入参数：
// 输出参数：
// 函数功能：
/******************************************************************************/
void main ( void )
{
    unsigned char i = 0;

    unsigned int count_send = 0;
    unsigned int rec_new = 0;
    unsigned int rec_old = 0;
    unsigned int rec_err = 0;
    unsigned int lock_key = 0;
    uartInit();

    Delay100ms();
    init_nrf24l01_io();
    led = 0;
    Delay100ms();
    led = 1;
    Delay100ms();
    led = 0;
    Delay100ms();
    led = 1;
    Delay100ms();
    TI = 1;
    Delay100ms();
    uartSendString ( "READY!\r\n" );
    ifnnrf_rx_mode();

    while ( 1 )
    {

        KEY = 1;
        KEY2 = 1;

        while ( KEY == 0 || KEY2 == 0 )
        {
            IRQ = 1;
            SPI_RW_Reg ( WRITE_REG + STATUS, 0xff );

            if ( KEY == 0 )
            {
                tx_buf[0] = 0xAA;
            }
            else if ( KEY2 == 0 )
            {
                tx_buf[0] = 0x55;
            }

            ifnnrf_tx_mode();

            while ( IRQ );

            sta = SPI_Read ( STATUS );
            SPI_RW_Reg ( WRITE_REG + STATUS, 0xff );

            if ( sta & STA_MARK_TX )
            {
                if ( KEY == 0 )
                {
                    led = 0;
                    Delay100ms();
                    led = 1;
                    Delay100ms();
                }
                else
                {
                    led2 = 0;
                    Delay100ms();
                    led2 = 1;
                    Delay100ms();
                }
            }
            else
            {
                ifnnrf_CLERN_ALL();
            }

            lock_key = 1;

        }	//发送

        if ( lock_key )
        {
            lock_key = 0;
            ifnnrf_rx_mode();
            IRQ = 1;

            while ( IRQ == 0 );

            _delay_us ( 400 );
        }

        IRQ = 1;

        if ( IRQ == 0 )
        {
            sta = SPI_Read ( STATUS );
            SPI_RW_Reg ( WRITE_REG + STATUS, 0xff );

            if ( sta & STA_MARK_RX )
            {
                SPI_Read_Buf ( RD_RX_PLOAD, rx_buf, TX_PLOAD_WIDTH );

                if ( rx_buf[0] == 0xAA )
                {
                    uartSendString ( "你按下了左边按键\r\n" );
                    led = 0;
                    Delay100ms();
                    led = 1;
                    Delay100ms();
                }
                else if ( rx_buf[0] == 0x55 )
                {
                    uartSendString ( "你按下了右边按键\r\n" );
                    led2 = 0;
                    Delay100ms();
                    led2 = 1;
                    Delay100ms();
                }

                rx_buf[0] = 0;
            }
            else
            {
                ifnnrf_CLERN_ALL();
                ifnnrf_rx_mode();
                IRQ = 1;

                while ( IRQ == 0 );
            }
        } //接收

    }
}